View LTC1553L_337171.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LTC1553L 5-Bit Programmable Synchronous Switching Regulator Controller for Pentium(R) II Processor
FEATURES
s s
DESCRIPTION
The LTC(R)1553L is a high power, high efficiency switching regulator controller optimized for a 5V input to 1.8V-3.5V output applications. It features a digitally programmable output voltage, a precision internal reference and an internal feedback system that provides output accuracy of 1.5% at room temperature and typically 2% over-temperature, load current and line voltage shifts. The LTC1553L uses a synchronous switching architecture with two external N-channel output devices, providing high efficiency and eliminating the need for a high power, high cost P-channel device. Additionally, it senses the output current across the on-resistance of the upper N-channel FET, providing an adjustable current limit without an external low value sense resistor. The LTC1553L free-runs at 300kHz and can be synchronized to a faster external clock if desired. It includes all the inputs and outputs required to implement a power supply conforming to the Intel Pentium(R) II Processor VRM 8.2 DC/DC Converter Specification.
, LTC and LT are registered trademarks of Linear Technology Corporation. Pentium is a registered trademark of Intel Corporation.
s
s s s s
s s
s s
5-Bit Digitally Programmable 1.8V to 3.5V Fixed Output Voltage Provides All Features Required by the Intel Pentium(R) II Processor VRM 8.2 DC/DC Converter Specification Flags for Power Good, Over-Temperature and Overvoltage Fault 19A Output Current Capability from a 5V Supply Dual N-Channel MOSFET Synchronous Driver Initial Output Accuracy: 1.5% Excellent Output Accuracy: 2% Typ Over Line, Load and Temperature Variations High Efficiency: Over 95% Possible Adjustable Current Limit Without External Sense Resistors Fast Transient Response Available in 2O-Lead SSOP and SW Packages
APPLICATIONS
s s
Power Supply for Pentium II, SPARC, ALPHA and PA-RISC Microprocessors High Power 5V to 1.8V-3.5V Regulators
TYPICAL APPLICATION
+
0.1F 5.6k 5.6k 5.6k VCC IMAX 10F 2.7k
PVCC 12V
+
0.1F 10F
PWRGD PENTIUM(R) II SYSTEM FAULT 5 OT VID0 TO VID4 OUTEN COMP C1 150pF RC 8.2k CC 0.01F SS
PVCC G1 20 Q1* LO 2H 18A COUT 330F x7 VOUT 1.8V TO 3.5V 14A
LTC1553L
IFB
G2 SGND GND SENSE
CSS 0.1F
0.1F
*SILICONIX SUD50N03-10 **SANYO 10MV1200GX COILTRONICS CTX02-13198 OR PANASONIC 12TS-2R5SP AVX TPSE337M006R0100
Figure 1. 5V to 1.8V-3.5V Supply Application
U
VIN 5V
U
U
+
CIN** 1200F x4
+
Q2*
1553L F01
1
LTC1553L
ABSOLUTE MAXIMUM RATINGS
(Note 1)
PACKAGE/ORDER INFORMATION
TOP VIEW G2 PVCC GND SGND VCC SENSE IMAX IFB SS 1 2 3 4 5 6 7 8 9 20 G1 19 OUTEN 18 VID0 17 VID1 16 VID2 15 VID3 14 VID4 13 PWRGD 12 FAULT 11 OT
Supply Voltage VCC ........................................................................ 7V PVCC ................................................................... 14V Input Voltage IFB (Note 2) ............................................ PVCC + 0.3V IMAX ........................................................ - 0.3V to 9V All Other Inputs ......................... - 0.3V to VCC + 0.3V Digital Output Voltage ................................. - 0.3V to 9V IFB Input Current (Notes 2, 3) .......................... - 100mA Operating Temperature Range ..................... 0C to 70C Storage Temperature Range ................. - 65C to 150C Lead Temperature (Soldering, 10 sec.)................. 300C
ORDER PART NUMBER LTC1553LCG LTC1553LCSW
COMP 10
G PACKAGE SW PACKAGE 20-LEAD PLASTIC SSOP 20-LEAD PLASTIC SO
TJMAX = 125C, JA = 100C/ W (G) TJMAX = 125C, JA = 100C/ W (SW)
Consult factory for Industrial and Military grade parts.
ELECTRICAL CHARACTERISTICS
SYMBOL VCC PVCC VFB VOUT PARAMETER Supply Voltage Supply Voltage for G1, G2 Internal Feedback Voltage 1.8V Initial Output Voltage 2.8V Initial Output Voltage 3.5V Initial Output Voltage 1.8V Initial Output Voltage 2.8V Initial Output Voltage 3.5V Initial Output Voltage Output Load Regulation Output Line Regulation Positive Power Good Trip Point Negative Power Good Trip Point FAULT Trip Point Operating Supply Current Shutdown Supply Current Supply Current Internal Oscillator Frequency VCOMP at Minimum Duty Cycle VCOMP at Maximum Duty Cycle Error Amplifier Open-Loop DC Gain Error Amplifier Transconductance Error Amplifier -3dB Bandwidth (Note 4) CONDITIONS
VCC = 5V, PVCC = 12V, TA = 25C, unless otherwise noted. (Note 3)
MIN
q q
TYP
MAX 6 13.2
UNITS V V V mV mV mV mV mV mV mV mV
4.5 1.260
With Respect to Rated Output Voltage (Figure 2)
- 27 (- 1.5%) - 42 (- 1.5%) - 52 (- 1.5%) q - 36 (- 2%) q - 56 (- 2%) q - 70 (- 2%) -5 1
q q q q q
27 (+ 1.5%) 42 (+ 1.5%) 52 (+ 1.5%) 36 (+ 2%) 56 (+ 2%) 70 (+ 2%)
VOUT VPWRGD VFAULT ICC IPVCC fOSC VSAWL VSAWH GERR gmERR BWERR
IOUT = 0 to 14A (Note 4) (Figure 2) VIN = 4.75V to 5.25V, IOUT = 0 (Note 4)(Figure 2) % Above Output Voltage (Figure 2) % Below Output Voltage (Figure 2) % Above Output Voltage (Figure 2) OUTEN = VCC = 5V (Note 5)(Figure 3) OUTEN = 0, VID0 to VID4 Floating (Figure 3) PVCC = 12V, OUTEN = VCC (Note 6) (Figure 3) PVCC = 12V, OUTEN = 0, VID0 to VID4 Floating (Figure 4) (Note 4) (Note 4) (Note 7) (Note 7) COMP = Open (Note 4)
q q q
-7 12
5 -5 15 800 130 15 1
7 20 1200 250
250
300 1.8 2.8
350
40 0.9
53 1.6 400 2.3
millimho kHz
2
U
W
U
U
WW
W
% % % A A mA A kHz V V dB
LTC1553L
ELECTRICAL CHARACTERISTICS
SYMBOL IIMAX ISS ISSIL ISSHIL tSSHIL tPWRGD tPWRBAD tFAULT tOT VOT VOTDD VSHDN t r, t f t NOL DCMAX VIH VIL RIN ISINK PARAMETER IMAX Sink Current Soft Start Source Current Maximum Soft Start Sink Current Under Current Limit Soft Start Sink Current Under Hard Current Limit Hard Current Limit Hold Time Power Good Response Time Power Good Response Time FAULT Response Time OT Response Time Over-Temperature Trip Point Over-Temperature Driver Disable Shutdown Driver Rise and Fall Time Driver Nonoverlap Time Maximum G1 Duty Cycle VID0 to VID4 Input High Voltage VID0 to VID4 Input Low Voltage VID0 to VID4 Internal Pull-Up Resistance Digital Output Sink Current CONDITIONS VIMAX = VCC
VCC = 5V, PVCC = 12V, TA = 25C, unless otherwise noted. (Note 3)
MIN
q q q q
TYP 180 - 11 60 45 500
MAX 220 -8 150
UNITS A A A mA s
150 - 15 30 20
VSS = 0V, VIMAX = 0V, VIFB = VCC VSENSE = VOUT, VIMAX = VCC, VIFB = 0V (Notes 8, 9), VSS = VCC VSENSE = 0V, VIMAX = VCC, VIFB = 0V VSENSE = 0V, VIMAX = 4V, VIFB from 5V (Note 4) VSENSE from 0V to Rated VOUT VSENSE from Rated VOUT to 0V VSENSE from Rated VOUT to VCC OUTEN, VID0 to VID4 = 0 (Note 10) (Figure 3) OUTEN, VID0 to VID4 = 0 (Note 10) (Figure 3) OUTEN, VID0 to VID4 = 0 (Note 10) (Figure 3) OUTEN, VID0 to VID4 = 0 (Note 10) (Figure 3) (Figure 4) (Figure 4) (Figure 4)
q q q q q q q q q q q q q q
0.5 200 200 15 1.9 1.6
1 500 500 40 2 1.7 90
2 1000 1000 60 2.12 1.8 0.8 150 90 0.8
ms s s s V V V ns ns % V V k mA
30 77 2 10 10
100 85
20
The q denotes specifications which apply over the full operating temperature range. Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: When IFB is taken below GND, it will be clamped by an internal diode. This pin can handle input currents greater than 100mA below GND without latchup. In the positive direction, it is not clamped to VCC or PVCC. Note 3: All currents into device pins are positive; all currents out of the device pins are negative. All voltages are referenced to ground unless otherwise specified. Note 4: This parameter is guaranteed by correlation and is not tested directly. Note 5: The LTC1553L goes into the shutdown mode if VID0 to VID4 are floating. Due to the internal pull-up resistors, there will be an additional 0.25mA/pin if any of the VID0 to VID4 pins are pulled low.
Note 6: Supply current in normal operation is dominated by the current needed to charge and discharge the external FET gates. This will vary with the LTC1553L operating frequency, supply voltage and the external FETs used. Note 7: The open-loop DC gain and transconductance from the SENSE pin to COMP pin will be (GERR)(1.260/3.3) and (gmERR)(1.260/3.3) respectively. Note 8: The current limiting amplifier can sink but cannot source current. Under normal (not current limited) operation, the output current will be zero. Note 9: Under typical soft current limit, the net soft start discharge current will be 60A (ISSIL) + [-11A(ISS)] 50A. The soft start sink-to-source current ratio is designed to be 5.5:1. Note 10: When VID0 to VID4 are all HIGH, the LTC1553L will be forced to shut down internally. The OUTEN trip voltages are guaranteed by design for all other input codes.
3
LTC1553L TYPICAL PERFORMANCE CHARACTERISTICS
Typical 2.8V VOUT Distribution
140 120
TOTAL SAMPLE SIZE = 1500
NUMBER OF UNITS
100
OUTPUT VOLTAGE (V)
EFFICIENCY (%)
80 25C 60 40 20 0 2.775 100C
2.785
2.815 2.795 2.805 OUTPUT VOLTAGE (V)
Line Regulation
2.825 2.820 2.815 REFER TO TYPICAL APPLICATION CIRCUIT FIGURE 1 OUTPUT = NO LOAD TA = 25C
2.840
OVER-TEMPERATURE TRIP POINT (V)
OUTPUT VOLTAGE (V)
2.810 2.805 2.800 2.795 2.790 2.785 2.780 2.775 4.75 4.85 5.05 5.15 4.95 INPUT VOLTAGE (V) 5.25
1553L G04
OUTPUT VOLTAGE (V)
1.78 1.76 1.74 1.72 1.70 1.68 1.66 1.64 1.62 1.60 -50 -25 50 25 0 75 TEMPERATURE (C) 100 125
2.1 1.9 1.7 1.5 1.3 1.1 0.9 - 50 -25
ERROR AMPLIFIER OPEN-LOOP DC GAIN (dB)
1.80
OVER-TEMPERATURE DRIVER DISABLE (V)
ERROR AMPLIFIER TRANSCONDUCTANCE (millimho)
Over-Temperature Driver Disable vs Temperature
4
UW
1553L G01
1553L G07
Efficiency vs Load Current
100 90 80 70 60 50 40 30 20 10 0
2.825
Load Regulation
2.825 REFER TO TYPICAL APPLICATION 2.820 CIRCUIT FIGURE 1 V = 5V, PVCC = 12V, TA = 25C 2.815 IN 2.810 2.805 2.800 2.795 2.790 2.785 2.780 2.775 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 OUTPUT CURRENT (A)
1533L G03
A
B
REFER TO TYPICAL APPLICATION CIRCUIT FIGURE 1 VIN = 5V, PVCC = 12V, VOUT = 2.8V, COUT = 330F x 7, LO = 2H A: Q1 = 1 x SUD50N03-10 Q2 = 1 x SUD50N03-10 B: Q1 = 2 x SUD50N03-10 Q2 = 1 x SUD50N03-10 NO FAN Q1 IS MOUNTED ON 1IN2 COPPER AREA 0 0.3 2 4 6 8 10 LOAD CURRENT (A) 12 14
1533L G02
Output Temperature Drift
2.860 2.850 2.830 2.820 2.810 2.800 2.790 2.780 2.770 2.660 2.750 2.740 - 50 - 25 50 0 75 25 TEMPERATURE (C) 100 125 2.12 2.10 2.08 2.06 2.04 2.02 2.00 1.98 1.96 1.94 1.92
Over-Temperature Trip Point vs Temperature
1.90 - 50 - 25
50 0 75 25 TEMPERATURE (C)
100
125
1553L G05
1553L G06
Error Amplifier Transconductance vs Temperature
2.3 60
Error Amplifier Open-Loop DC Gain vs Temperature
55
50
45
50 25 75 0 TEMPERATURE (C)
100
125
40 -50
-25
75 0 25 50 TEMPERATURE (C)
100
125
1553L G08
1553L G09
LTC1553L TYPICAL PERFORMANCE CHARACTERISTICS
Oscillator Frequency vs Temperature
350 340 220 210 IMAX SINK CURRENT (A) 200 190 180 170 160 150 -50
SOFT START SOURCE CURRENT (A)
OSCILLATOR FREQUENCY (kHz)
330 320 310 300 290 280 270 260 250 -50 -25 50 25 0 75 TEMPERATURE (C) 100 125
Maximum G1 Duty Cycle vs Temperature
92 1.2 90 88 86 84 82 80 78 - 50 - 25 50 25 75 0 TEMPERATURE (C) 100 125 5500pF 7700pF G1, G2 CAPACITANCE = 1100pF 2200pF 3300pF
VCC OPERATING SUPPLY CURRENT (mA)
VCC SHUTDOWN SUPPLY CURRENT (mA)
OSCILLATOR FREQUENCY = 300kHz
MAXIMUM G1 DUTY CYCLE (%)
PVCC Supply Current vs Gate Capacitance
70 60
PVCC SUPPLY CURRENT (mA)
PVCC = 12V TA = 25C
50 40 30 20 10 0 0 2000 6000 GATE CAPACITANCE (pF) 4000 8000
1553L G16
OUTPUT VOLTAGE (V)
UW
1553L G10
IMAX Sink Current vs Temperature
-8 -9 -10 -11 -12 -13 -14
Soft Start Source Current vs Temperature
-25
75 0 50 25 TEMPERATURE (C)
100
125
-15 - 50 - 25
50 25 75 0 TEMPERATURE (C)
100
125
1553L G11
1553L G12
VCC Operating Supply Current vs Temperature
250 VCC = 5V fOSC = 300kHz 225 200 175 150 125 100 75 1.1 1.0 0.9 0.8 0.7 0.6 0.5 - 50 -25
VCC Shutdown Supply Current vs Temperature
50 25 75 0 TEMPERATURE (C)
100
125
50 - 50 - 25
0
50 75 25 TEMPERATURE (C)
100
125
1553L G13
1553L G14
1553L G15
Output Over Current Protection
3.0 2.5 2.0 1.5 Q1 CASE = 90C, VOUT = 2.8V Q1 = 2 x MTD20N03HDL Q2 = 1 x MTD20N03HDL RIMAX = 2.7k, RIFB = 20, SS CAP = 0.01F
Transient Response
50mV/DIV
5A/DIV
1.0 SHORT-CIRCUIT CURRENT 0.5 0 0 2 4 6 8 10 12 14 OUTPUT CURRENT (A) 16 18
1553L G18
100s/DIV
1553L G17
5
LTC1553L
PIN FUNCTIONS
G2 (Pin 1): Gate Drive for the Lower N-Channel MOSFET, Q2. This output will swing from PVCC to GND. It will always be low when G1 is high or when the output is disabled. To prevent undershoot during a soft start cycle, G2 is held low until G1 first goes high. PVCC (Pin 2): Power Supply for G1 and G2. PVCC must be connected to a potential of at least VIN + VGS(ON)Q1. If VIN = 5V, PVCC can be generated using a simple charge pump connected to the switching node between Q1 and Q2 (see Figure 7), or it can be connected to an auxiliary 12V supply if one exists. GND (Pin 3): Power Ground. GND should be connected to a low impedance ground plane in close proximity to the source of Q2. SGND (Pin 4): Signal Ground. SGND is connected to the low power internal circuitry and should be connected to the negative terminal of the output capacitor where it returns to the ground plane. GND and SGND should be shorted right at the LTC1553L. VCC (Pin 5): Power Supply. Power for the internal low power circuity. VCC should be wired separately from the drain of Q1 if they share the same supply. A 10F bypass capacitor is recommended from this pin to SGND. SENSE (Pin 6): Output Voltage Pin. Connect to the positive terminal of the output capacitor. There is an internal 120k resistor connected from this pin to SGND. SENSE is a very sensitive pin; for optimum performance, connect an external 0.1F capacitor from this pin to SGND. By connecting a small external resistor between the output capacitor and the SENSE pin, the initial output voltage can be raised slightly. Since the internal divider has a nominal impedance of 120k, a 1200 series resistor will raise the nominal output voltage by 1%. If an external resistor is used, the value of the 0.1F capacitor on the SENSE pin must be greatly reduced or loop phase margin will suffer. Set a time constant for the RC combination of approximately 0.1s. So, for example, with a 1200 resistor, set C = 83pF. Use a standard 100pF capacitor. IMAX (Pin 7): Current Limit Threshold. Current limit is set by the voltage drop across an external resistor connected between the drain of Q1 and IMAX. There is a 180A internal pull-down at IMAX. IFB (Pin 8): Current Limit Sense Pin. Connect to the switching node between the source of Q1 and the drain of Q2. If IFB drops below IMAX when G1 is on, the LTC1553L will go into current limit. The current limit circuit can be disabled by floating IMAX and shorting IFB to VCC through an external 10k resistor. SS (Pin 9): Soft Start. Connect to an external capacitor to implement a soft start function. During moderate overload conditions, the soft start capacitor will be discharged slowly in order to reduce the duty cycle. In hard current limit, the soft start capacitor will be forced low immediately and the LTC1553L will rerun a complete soft start cycle. CSS must be selected such that during power-up the current through Q1 will not exceed the current limit value. COMP (Pin 10): External Compensation. The COMP pin is connected directly to the output of the error amplifier and the input of the PWM comparator. An RC + C network is used at this node to compensate the feedback loop to provide optimum transient response. OT (Pin 11): Over-Temperature Fault. OT is an open-drain output and will be pulled low if OUTEN is less than 2V. If OUTEN = 0, OT pulls low. FAULT (Pin 12): Overvoltage Fault. FAULT is an opendrain output. If VOUT reaches 15% above the nominal output voltage, FAULT will go low and G1 and G2 will be disabled. Once triggered, the LTC1553L will remain in this state until the power supply is recycled or the OUTEN pin is toggled. If OUTEN = 0, FAULT floats or is pulled high by an external resistor. PWRGD (Pin 13): Power Good. This is an open-drain signal to indicate validity of output voltage. A high indicates that the output has settled to within 5% of the rated output for more than 1ms. PWRGD will go low if the output is out of regulation for more than 500s. If OUTEN = 0, PWRGD pulls low.
6
U
U
U
LTC1553L
PIN FUNCTIONS
VID0, VID1, VID2, VID3, VID4 (Pins 18, 17, 16, 15, 14): Digital Voltage Select. TTL inputs used to set the regulated output voltage required by the processor (Table 3). There is an internal 20k pull-up at each pin. When all five VIDn pins are high or floating, the chip will shut down. OUTEN (Pin 19): Output Enable. TTL input which enables the output voltage. The external MOSFET temperature can be monitored with an external thermistor as shown in Figure 11. When the OUTEN input voltage drops below 2V, OT trips. As OUTEN drops below 1.7V, the drivers are internally disabled to prevent the MOSFETs from heating further. If OUTEN is less than 1.2V for longer than 30s, the LTC1553L will enter shutdown mode. The internal oscillator can be synchronized to a faster external clock by applying the external clocking signal to the OUTEN pin. G1 (Pin 20): Gate Drive for the Upper N-Channel MOSFET, Q1. This output will swing from PVCC to GND. It will always be low when G2 is high or the output is disabled.
BLOCK DIAGRAM
115% VREF
+
FC 12 FAULT 11 OT DELAY LOGIC DISDR SYSTEM POWER DOWN 13 PWRGD
-
OUTEN 19
COMP 10 ISS SS 9 QSS
ERR
+
-
VREF
MHCL
HCL MONO
+
-
W
U
U
U
2 PVCC
R PWM S
20 G1
1 G2
BG MIN MAX
-
+
-
+
FB
6 SENSE 18 VID0 17 VID1 16 VID2
VREF - 5%
VREF + 5%
-
CC
8 IFB
15 VID3 14 VID4 DAC
+
7 IMAX IMAX
VREF
+
LVC
0.5VREF / 0.7VREF
-
1553 BD
7
LTC1553L
TEST CIRCUITS
VCC 5V PVCC 12V VIN 5V
+
3k 3k 3k 10F 0.1F 10F
+
0.1F 10k IFB G1 LTC1553L IMAX G2 SGND GND SENSE NC Q2*
+
CIN** 1200F x4
100pF
100pF
OUTEN PWRGD FAULT OT
VCC
PVCC
LO Q1* 2H 15A VOUT COUT 330F x7
100pF
VID0 TO VID4
VID0 TO VID4 COMP SS
+
C1 150pF
RC 8.2k CC 0.01F
0.1F
0.1F
*SILICONIX SUD50N03-10 **SANYO 10MV1200GX COILTRONICS CTX02-13198 OR PANASONIC 12TS-2R5SP AVX TPSE337M006R0100
1553L F02
Figure 2
VCC VID0 VID1 VID2 VID3 VID4 10k VID0 VID1 VID2 VID3 VID4 OUTEN NC NC NC NC PWRGD FAULT OT COMP SS NC
1553L F03
VCC
+
0.1F PVCC 10F
VCC
IFB PVCC G1 NC NC NC
+
0.1F 10F
LTC1553L IMAX G2 SGND GND SENSE
Figure 3
VCC 5V
PVCC 12V tr tf 90% 50% G1 5000pF G1 RISE/FALL 10% 90% 50% 10%
+
10F 0.1F 10k VCC IFB LTC1553L PVCC 0.1F
+
10F
t NOL SENSE SGND GND G2 5000pF G2 RISE/FALL 50%
t NOL
50%
1553L F04
Figure 4
8
LTC1553L
FU CTIO TABLES
Table 1. OT Logic
OUTEN (V) <2 >2 OT* 0 1 VID4 0 0 0 OUTPUT* OT 0 1 1 1 1 FAULT 1 1 1 1 0 PWRGD 0 0 1 0 0 X < 95% > 95% < 105% >105% > 115% 0 0 0 1 1 1 1 1 1 RATED OUTPUT VOLTAGE (V) Disabled (1.30) Disabled (1.35) Disabled (1.40) Disabled (1.45) Disabled (1.50) Disabled (1.55) Disabled (1.60) Disabled (1.65) Disabled (1.70) Disabled (1.75) 1 1 1 1 1 1 1 1 1 1 VID3 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Table 2. PWRGD and FAULT Logic
INPUT OUTEN 0 1 1 1 1 VSENSE**
Table 3. Rated Output Voltage
INPUT PIN VID4 0 0 0 0 0 0 0 0 0 0 VID3 1 1 1 1 1 1 1 1 0 0 VID2 1 1 1 1 0 0 0 0 1 1 VID1 1 1 0 0 1 1 0 0 1 1 VID0 1 0 1 0 1 0 1 0 1 0
U
U
Table 3. Rated Output Voltage (cont)
INPUT PIN VID2 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 VID1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 VID0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 RATED OUTPUT VOLTAGE (V) 1.80 1.85 1.90 1.95 2.00 2.05 SHDN 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5
* With external pull-up resistor ** With respect to the output voltage selected in Table 3 as required by Intel Specification VRM 8.2 These code selections are disabled in LTC1553L X Don't care
9
LTC1553L
APPLICATIONS INFORMATION
OVERVIEW The LTC1553L is a voltage feedback, synchronous switching regulator controller (see Block Diagram) designed for use in high power, low voltage step-down (buck) converters. It is designed to satisfy the requirements of the Intel Pentium II power supply specification. It includes an on-chip DAC to control the output voltage, a PWM generator, a precision reference trimmed to 1%, two high power MOSFET gate drivers and all the necessary feedback and control circuitry to form a complete switching regulator circuit. The LTC1553L includes a current limit sensing circuit that uses the upper external power MOSFET as a current sensing element, eliminating the need for an external sense resistor. Once the current comparator, CC, detects an overcurrent condition, the duty cycle is reduced by discharging the soft start capacitor through a voltagecontrolled current source. Under severe overloads or output short circuit conditions, the chip will be repeatedly forced into soft start until the short is removed, preventing the external components from being damaged. Under output overvoltage conditions, the MOSFET drivers will be disabled permanently until the chip power supply is recycled or the OUTEN pin is toggled. OUTEN can optionally be connected to an external negative temperature coefficient (NTC) thermistor placed near the external MOSFETs or the microprocessor. Three threshold levels are provided internally. When OUTEN drops to 2V, OT will trip, issuing a warning to the external CPU. If the temperature continues to rise and the OUTEN input drops to 1.7V, the G1 and G2 pins will be forced low. If OUTEN is pulled below 1.2V, the LTC1553L will go into shutdown mode, cutting the supply current to a minimum. If thermal shutdown is not required, OUTEN can be connected to a conventional TTL enable signal. The freerunning 300kHz PWM frequency can be synchronized to a faster external clock connected to OUTEN. Adjusting the oscillator frequency can add flexibility in the external component selection. See the Clock Synchronization section. Output regulation can be monitored with the PWRGD pin which in turn monitors the internal MIN and MAX comparators. If the output is 5% beyond the selected value for more than 500s, the PWRGD output will be pulled low. Once the output has settled within 5% of the selected value for more than 1ms, PWRGD will return high. THEORY OF OPERATION Primary Feedback Loop The regulator output voltage at the SENSE pin is divided down internally by a resistor divider with a total resistance of approximately 120k. This divided down voltage is subtracted from a reference voltage supplied by the DAC output. The resulting error voltage is amplified by the error amplifier and the output is compared to the oscillator ramp waveform by the PWM comparator. This PWM signal controls the external MOSFETs through G1 and G2. The resulting chopped waveform is filtered by LO and COUT closing the loop. Loop frequency compensation is achieved with an external RC + C network at the COMP pin, which is connected to the output node of the transconductance amplifier. MIN, MAX Feedback Loops Two additional comparators in the feedback loop provide high speed fault correction in situations where the ERR amplifier may not respond quickly enough. MIN compares the feedback signal FB to a voltage 60mV (5%) below the internal reference. If FB is lower than the threshold of this comparator, the MIN comparator overrides the ERR amplifier and forces the loop to full duty cycle which is set by the internal oscillator typically to 85%. Similarly, the MAX comparator forces the output to 0% duty cycle if FB is more than 5% above the internal reference. To prevent these two comparators from triggering due to noise, the MIN and MAX comparators' response times are deliberately controlled so that they take two to three microseconds to respond. These two comparators help prevent extreme output perturbations with fast output transients, while allowing the main feedback loop to be optimally compensated for stability.
10
U
W
U
U
LTC1553L
APPLICATIONS INFORMATION
Soft Start and Current Limit The LTC1553L includes a soft start circuit which is used for initial start-up and during current limit operation. The SS pin requires an external capacitor to GND with the value determined by the required soft start time. An internal 11A current source is included to charge the external SS capacitor. During start-up, the COMP pin is clamped to a diode drop above the voltage at the SS pin. This prevents the error amplifier, ERR, from forcing the loop to maximum duty cycle. The LTC1553L will begin to operate at low duty cycle as the SS pin rises above about 1.2V (VCOMP 1.8V). As SS continues to rise, QSS turns off and the error amplifier begins to regulate the output. The MIN comparator is disabled when soft start is active to prevent it from overriding the soft start function. The LTC1553L includes yet another feedback loop to control operation in current limit. Just before every falling edge of G1, the current comparator, CC, samples and holds the voltage drop measured across the external MOSFET, Q1, at the IFB pin. CC compares the voltage at IFB to the voltage at the IMAX pin. As the peak current rises, the measured voltage across Q1 increases due to the drop across the RDS(ON) of Q1. When the voltage at IFB drops below IMAX, indicating that Q1's drain current has exceeded the maximum level, CC starts to pull current out of the external soft start capacitor, cutting the duty cycle and controlling the output current level. The CC comparator pulls current out of the SS pin in proportion to the voltage difference between IFB and IMAX. Under minor overload conditions, the SS pin will fall gradually, creating a time delay before current limit takes effect. Very short, mild overloads may not affect the output voltage at all. More significant overload conditions will allow the SS pin to reach a steady state, and the output will remain at a reduced voltage until the overload is removed. Serious overloads will generate a large overdrive at CC, allowing it to pull SS down quickly and preventing damage to the output components. By using the RDS(ON) of Q1 to measure the output current, the current limiting circuit eliminates an expensive discrete sense resistor that would otherwise be required. This helps minimize the number of components in the high current path. Due to switching noise and variation of RDS(ON), the actual current limit trip point is not highly accurate. The current limiting circuitry is primarily meant to prevent damage to the power supply circuitry during fault conditions. The exact current level where the limiting circuit begins to take effect will vary from unit to unit as the RDS(ON) of Q1 varies. For a given current limit level, the external resistor from IMAX to VIN can be determined by:
U
W
U
U
RIMAX =
where,
(ILMAX )(RDS(ON)Q1)
IIMAX
I ILMAX = ILOAD + RIPPLE 2
ILOAD = Maximum load current IRIPPLE = Inductor ripple current
=
(VIN - VOUT )(VOUT ) (fOSC )(L O)(VIN)
fOSC = LTC1553L oscillator frequency = 300kHz LO = Inductor value RDS(ON)Q1 = Hot on-resistance of Q1 at ILMAX IIMAX = Internal 180A sink current at IMAX
VIN LTC1553L IMAX RIMAX
+
CIN
+
CC 180A
7 G1 IFB 20 8 Q1 LO VOUT
-
+
G2 Q2 COUT
1553L F05
Figure 5. Current Limit Setting
11
LTC1553L
APPLICATIONS INFORMATION
Table 4. Recommended Minimum RIMAX Resistor (k) vs Maximum Operating Load Current and External MOSFET Q1
MAXIMUM OPERATING LOAD CURRENT (A) 12 14 16 18 20 SUD50N03-10 2.4 2.7 3.0 3.6 3.9 SUD50N03-10 (TWO IN PARALLEL) 1.2 1.3 1.5 1.8 2.0
VCC 5.6k PENTIUM II SYSTEM VCC LTC1553L R1 R2 NTC THERMISTOR MOUNT IN CLOSE THERMAL PROXIMITY TO Q1 OUTEN G2 Q2 OT G1 Q1 LO VOUT
OUTEN and Thermistor Input The LTC1553L includes a low power shutdown mode, controlled by the logic at the OUTEN pin. A high at OUTEN allows the part to operate normally. A low level at OUTEN stops all internal switching, pulls COMP and SS to ground internally and turns Q1 and Q2 off. OT and PWRGD are pulled low, and FAULT is left floating. In shutdown, the LTC1553L quiescent current will drop to about 130A. The remaining current is used to keep the thermistor sensing circuit at OUTEN alive. Note that the leakage current of the external MOSFETs may add to the total shutdown current consumed by the circuit, especially at elevated temperature. OUTEN is designed with multiple thresholds to allow it to also be utilized for over-temperature protection. The power MOSFET operating temperature can be monitored with an external negative temperature coefficient (NTC) thermistor mounted next to the external MOSFET which is expected to run the hottest -- often the high-side device, Q1. Electrically, the thermistor should form a voltage divider with another resistor, R1, connected to VCC. Their midpoint should be connected to OUTEN (see Figure 6). As the temperature increases, the OUTEN pin voltage is reduced. Under normal operating conditions, the OUTEN pin should stay above 2V. All circuits will function normally, and the OT pin will remain in a high state. If the temperature gets abnormally high, the OUTEN pin voltage will eventually drop below 2V. OT will switch to a logic low, providing an over-temperature warning to the system. As OUTEN drops below 1.7V, the LTC1553L disables both FET drivers. If OUTEN is less than 1.2V, the LTC1553L will enter shutdown mode. To activate any of these three modes, the OUTEN voltage must drop below the respective threshold for longer than 30s.
12
U
W
U
U
MTD20N03HDL 4.3 5.1 6.2 6.8 7.5
MTD20N03HDL (TWO IN PARALLEL) 2.2 2.7 3.0 3.3 3.6
VIN
+
COUT
1553L F06
Figure 6. OUTEN Pin as a Thermistor Input
Clock Synchronization The internal oscillator can be synchronized to an external clock by applying the external clocking signal to the OUTEN pin. The synchronizing range extends from the initial operating frequency up to 500kHz. If the external frequency is much higher than the natural free-running frequency, the peak-to-peak sawtooth amplitude within the LTC1553L will decrease. Since the loop gain is inversely proportional to the amplitude of the sawtooth, the compensation network may need to be adjusted slightly. Note that the temperature sensing circuitry does not operate when external synchronization is used. MOSFET Gate Drive Power for the internal MOSFET drivers is supplied by PVCC. This supply must be above the input supply voltage by at least one power MOSFET VGS(ON) for efficient operation. This higher voltage can be supplied with a separate supply, or it can be generated using a simple charge pump as shown in Figure 7. The 85% typical maximum duty cycle ensures sufficient off-time to refresh the charge pump during each cycle.
LTC1553L
APPLICATIONS INFORMATION
OPTIONAL FOR VIN > 5V 1N5243B 13V LTC1553L G1 20 2 PVCC 0.1F 1N5817 VIN
+
Q1 LO VOUT
G2 1
+
Q2 COUT
1553L F07
Figure 7. Doubling Charge Pump
If the OUTEN pin is low, G1 and G2 are both held low to prevent output voltage undershoot. As VCC and PVCC power up from a 0V condition, an internal undervoltage lockup circuit prevents G1 and G2 from going high until VCC reaches about 3.5V. If VCC powers up while PVCC is at ground potential, the SS is forced to ground potential internally. SS clamps the COMP pin low and prevents the drivers from turning on. On power-up or recovery from thermal shutdown, the drivers are designed such that G2 is held low until G1 first goes high. Power MOSFETs Two N-channel power MOSFETs are required for most LTC1553L circuits. Logic level MOSFETs should be used and they should be selected based on on-resistance considerations. RDS(ON) should be chosen based on input and output voltage, allowable power dissipation and maximum required output current. In a typical LTC1553L buck converter circuit the average inductor current is equal to the output load current. This current is always flowing through either Q1 or Q2 with the power dissipation split up according to the duty cycle:
V DC Q1 = OUT VIN
()
VIN - VOUT V DC Q2 = 1 - OUT = VIN VIN
()
(
)
The RDS(ON) required for a given conduction loss can now be calculated by rearranging the relation P = I2R.
U
W
U
U
CIN
(VIN)PMAX(Q1) RDS(ON)Q1 = = 2 2 DC(Q1)](IMAX) (VOUT)(IMAX) [ PMAX(Q2) (VIN)PMAX(Q2) RDS(ON)Q2 = = 2 [DC(Q2)](IMAX) (VIN - VOUT)(IMAX)2
PMAX Q1
()
PMAX should be calculated based primarily on required efficiency or allowable thermal dissipation. A typical high efficiency circuit designed for Pentium II with a 5V input and a 2.8V, 11.2A output might allow no more than 4% efficiency loss at full load for each MOSFET. Assuming roughly 90% efficiency at this current level, this gives a PMAX value of: [(2.8)(11.2A/0.9)(0.04)] = 1.39W per FET and a required RDS(ON) of:
(5V)(1.39W) = 0.019 () 2 (2.8V)(11.2A) (5V)(1.39W) = 0.025 RDS(ON)Q2 = 2 (5V - 2.8V)(11.2A)
RDS ON Q1 = Note also that while the required RDS(ON) values suggest large MOSFETs, the dissipation numbers are only 1.39W per device or less--large TO-220 packages and heat sinks are not necessarily required in high efficiency applications. Siliconix Si4410DY or International Rectifier IRF7413 (both in SO-8) or Siliconix SUD50N03 or Motorola MTD20N03HDL (both in D PAK) are small footprint surface mount devices with RDS(ON) values below 0.03 at 5V of gate drive that work well in LTC1553L circuits. With higher output voltages, the RDS(ON) of Q1 may need to be significantly lower than that for Q2. These conditions can often be met by paralleling two MOSFETs for Q1 and using a single device for Q2. Note that using a higher PMAX value in the RDS(ON) calculations will generally decrease MOSFET cost and circuit efficiency while increasing MOSFET heat sink requirements.
13
LTC1553L
APPLICATIONS INFORMATION
Table 5. Recommended MOSFETs for LTC1553L Applications
RDS(ON) AT 25C (m) 19 20 35 23 7.5 14 28 37 TYPICAL INPUT CAPACITANCE CISS (pF) 3200 2700 880 2300 4025 1600 3300 1750 JC (C/W) 1.8 -- 1.67 2.5 1.0 1.8 1.0 2.08
PARTS Siliconix SUD50N03-10 TO-252 Siliconix Si4410DY SO-8 Motorola MTD20N03HDL D PAK SGS-Thomson STD20N03L D PAK Motorola MTB75N03HDL DD PAK IRF IRL3103S DD PAK IRF IRLZ44 TO-220 Fuji 2SK1388 TO-220
Note: Please refer to the manufacturer's data sheet for testing conditions and detail information.
Inductor Selection The inductor is often the largest component in the LTC1553L design and should be chosen carefully. Inductor value and type should be chosen based on output slew rate requirements, output ripple requirements and expected peak current. Inductor value is primarily controlled by the required current slew rate. The maximum rate of rise of current in the inductor is set by its value, the input-tooutput voltage differential and the maximum duty cycle of the LTC1553L. In a typical 5V input, 2.8V output application, the maximum current slew rate will be:
DCMAX
(VIN - VOUT) = 1.83
L L
A s
where L is the inductor value in H. With proper frequency compensation, the combination of the inductor and output capacitor will determine the transient recovery time. In general, a smaller value inductor will improve transient response at the expense of increased output ripple voltage and inductor core saturation rating. A 2H inductor would have a 0.9A/s rise time in this application, resulting in a 5.5s delay in responding to a 5A load current step. During
14
U
W
U
U
RATED CURRENT (A) 15 at 25C 10 at 100C 10 at 25C 8 at 75C 20 at 25C 16 at 100C 20 at 25C 14 at 100C 75 at 25C 59 at 100C 56 at 25C 40 at 100C 50 at 25C 36 at 100C 35 at 25C
TJMAX (C) 175 150 150 175 150 175 175 150
this 5.5s, the difference between the inductor current and the output current must be made up by the output capacitor, causing a temporary voltage droop at the output. To minimize this effect, the inductor value should usually be in the 1H to 5H range for most typical 5V input LTC1553L circuits. To optimize performance, different combinations of input and output voltages and expected loads may require different inductor values. Once the required value is known, the inductor core type can be chosen based on peak current and efficiency requirements. Peak current in the inductor will be equal to the maximum output load current plus half of the peak-topeak inductor ripple current. Ripple current is set by the inductor value, the input and output voltage and the operating frequency. The ripple current is approximately equal to:
IRIPPLE =
(VIN - VOUT)(VOUT) (fOSC)(LO)(VIN)
fOSC = LTC1553L oscillator frequency = 300kHz LO = Inductor value
LTC1553L
APPLICATIONS INFORMATION
Solving this equation with our typical 5V to 2.8V application with a 2H inductor, we get:
(2.2)(0.56) = 2AP-P (300kHz)(2H)
Peak inductor current at 11.2A load:
11.2A +
2A = 12.2A 2
The ripple current should generally be between 10% and 40% of the output current. The inductor must be able to withstand this peak current without saturating, and the copper resistance in the winding should be kept as low as possible to minimize resistive power loss. Note that in circuits not employing the current limit function, the current in the inductor may rise above this maximum under short circuit or fault conditions; the inductor should be sized accordingly to withstand this additional current. Inductors with gradual saturation characteristics are often the best choice. Input and Output Capacitors A typical LTC1553L design puts significant demands on both the input and the output capacitors. During constant load operation, a buck converter like the LTC1553L draws square waves of current from the input supply at the switching frequency. The peak current value is equal to the output load current plus 1/2 peak-to-peak ripple current, and the minimum value is zero. Most of this current is supplied by the input bypass capacitor. The resulting RMS current flow in the input capacitor will heat it up, causing premature capacitor failure in extreme cases. Maximum RMS current occurs with 50% PWM duty cycle, giving an RMS current value equal to IOUT /2. A low ESR input capacitor with an adequate ripple current rating must be used to ensure reliable operation. Note that capacitor manufacturers' ripple current ratings are often based on only 2000 hours (three months) lifetime at rated temperature. Further derating of the input capacitor ripple current beyond the manufacturer's specification is recommended to extend the useful life of the circuit. Lower operating temperature will have the largest effect on capacitor longevity.
U
W
U
U
The output capacitor in a buck converter sees much less ripple current under steady-state conditions than the input capacitor. Peak-to-peak current is equal to that in the inductor, usually 10% to 40% of the total load current. Output capacitor duty places a premium not on power dissipation but on ESR. During an output load transient, the output capacitor must supply all of the additional load current demanded by the load until the LTC1553L can adjust the inductor current to the new value. Output capacitor ESR results in a step in the output voltage equal to the ESR value multiplied by the change in load current. An 11A load step with a 0.05 ESR output capacitor will result in a 550mV output voltage shift; this is 19.6% of the output voltage for a 2.8V supply! Because of the strong relationship between output capacitor ESR and output load transient response, the output capacitor is usually chosen for ESR, not for capacitance value; a capacitor with suitable ESR will usually have a larger capacitance value than is needed for energy storage. Electrolytic capacitors rated for use in switching power supplies with specified ripple current ratings and ESR can be used effectively in LTC1553L applications. OS-CON electrolytic capacitors from SANYO and other manufacturers give excellent performance and have a very high performance/size ratio for electrolytic capacitors. Surface mount applications can use either electrolytic or dry tantalum capacitors. Tantalum capacitors must be surge tested and specified for use in switching power supplies. Low cost, generic tantalums are known to have very short lives followed by explosive deaths in switching power supply applications. AVX TPS series surface mount devices are popular surge tested tantalum capacitors that work well in LTC1553L applications. A common way to lower ESR and raise ripple current capability is to parallel several capacitors. A typical LTC1553L application might exhibit 5A input ripple current. SANYO OS-CON part number 10SA220M (220F/ 10V) capacitors feature 2.3A allowable ripple current at 85C; three in parallel at the input (to withstand the input ripple current) will meet the above requirements. Similarly, AVX TPSE337M006R0100 (330F/6V) have a rated maximum ESR of 0.1; seven in parallel will lower the net output capacitor ESR to 0.014. For low cost application, SANYO MV-GX series of capacitors can be used with acceptable performance.
15
LTC1553L
APPLICATIONS INFORMATION
Feedback Loop Compensation The LTC1553L voltage feedback loop is compensated at the COMP pin, attached to the output node of the internal gm error amplifier. The feedback loop can generally be compensated properly with an RC + C network from COMP to GND as shown in Figure 8a. Loop stability is affected by the values of the inductor, output capacitor, output capacitor ESR, error amplifier transconductance and error amplifier compensation network. The inductor and the output capacitor create a double pole at the frequency:
fLC = 1 2(LO)(COUT)
RC CC LTC1553L COMP 10 ERR 6 SENSE
C1 DAC
Figure 8a. Compensation Pin Hook-Up
The ESR of the output capacitor forms a zero at the frequency:
fESR = 1 2(ESR)(COUT)
fZ
LOOP GAIN
fSW = LTC1553L SWITCHING FREQUENCY fCO = CLOSED-LOOP CROSSOVER FREQUENCY
The compensation network at the error amplifier output is to provide enough phase margin at the 0dB crossover frequency for the overall closed-loop transfer function. The zero and pole from the compensation network are:
1 1 fZ = and fP = respectively. 2(RC)(CC) 2(RC)(C1)
- 20dB/DECADE
fLC
fESR
fCO
Figure 8b shows the Bode plot of the overall transfer function. The compensation value used in this design is based on the following criteria: fSW = 12fCO, fZ = fLC and fP = 5fCO. At the closed-loop frequency fCO, the attenuation due the LC filter and the input resistor divider is compensated by the gain of the PWM modulator and the gain of the error amplifier (gmERR)(RC). Although a mathematical approach to frequency compensation can be used, the added complication of input and/or output filters, unknown capacitor ESR, and gross operating point changes with input voltage, load current variations, all suggest a more practical empirical method. This can be done by injecting a transient current at the load and using an RC network box to iterate toward the final compensation values, or by obtaining the optimum loop response using a network analyzer to find the actual loop poles and zeros.
Figure 8b. Bode Plot of the LTC1553L Overall Transfer Function
Table 6. Suggested Compensation Network for 5V Input Application Using Multiple Paralleled 330F AVX TPS Output Capacitors
LO (H) 1 1 1 2.7 2.7 2.7 5.6 5.6 5.6 CO (F) 990 1980 4950 990 1980 4950 990 1980 4950 RC (k) 1.8 3.6 9.1 5.1 10 24 10 20 51 CC (F) 0.022 0.01 0.01 0.01 0.01 0.0047 0.01 0.0047 0.0036 C1 (pF) 680 330 120 220 120 47 120 56 22
16
-
+
U
W
U
U
1553L F08a
fP FREQUENCY
1553L F08b
LTC1553L
APPLICATIONS INFORMATION
Table 6 shows the suggested compensation components for 5V input applications based on the inductor and output capacitor values. The values were calculated using multiple paralleled 330F AVX TPS series surface mount tantalum capacitors as the output capacitor. The optimum component values might deviate from the suggested values slightly because of board layout and operating condition differences. An alternate output capacitor is the Sanyo MV-GX series. Using multiple parallel 1500F Sanyo MV-GX capacitors for the output capacitor, Table 7 shows the suggested compensation component value for a 5V input application based on the inductor and output capacitor values.
Table 7. Suggested Compensation Network for 5V Input Application Using Multiple Paralleled 1500F SANYO MV-GX Output Capacitors
LO (H) 1 1 1 2.7 2.7 2.7 5.6 5.6 5.6 CO (F) 4500 6000 9000 4500 6000 9000 4500 6000 9000 RC (k) 4.3 5.6 8.2 11 15 22 24 30 47 CC (F) 0.022 0.0047 0.01 0.01 0.01 0.01 0.01 0.0047 0.0047 C1 (pF) 270 220 150 100 82 56 56 39 27
VID0 to VID4, PWRGD and FAULT The digital inputs (VID0 to VID4) program the internal DAC which in turn controls the output voltage. These digital input controls are intended to be static and are not designed for high speed switching. Forcing VOUT to step from a high to a low voltage by changing the VIDn pins quickly can cause FAULT to trip. Figure 9 shows the relationship between the VOUT voltage, PWRGD and FAULT. To prevent PWRGD from interrupting the CPU unnecessarily, the LTC1553L has a built-in tPWRBAD delay to prevent noise at the SENSE pin from toggling PWRGD. The internal time delay is designed to take about 500s for PWRGD to go low and 1ms for it to recover. Once PWRGD goes low, the internal circuitry watches for the output voltage to exceed 115% of the rated voltage. If
U
W
U
U
this happens, FAULT will be triggered. Once FAULT is triggered, G1 and G2 will be forced low immediately and the LTC1553L will remain in this state until VCC power supply is recycled or OUTEN is toggled.
15% VOUT 5% RATED VOUT -5% t PWRBAD PWRGD t PWRGD t FAULT
FAULT
1553L F09
Figure 9. PWRGD and FAULT
LAYOUT CONSIDERATIONS When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the LTC1553L. These items are also illustrated graphically in the layout diagram of Figure 10. The thicker lines show the high current paths. Note that at 10A current levels or above, current density in the PC board itself is a serious concern. Traces carrying high current should be as wide as possible. For example, a PCB fabricated with 2oz copper requires a minimum trace width of 0.15" to carry 10A. 1. In general, layout should begin with the location of the power devices. Be sure to orient the power circuitry so that a clean power flow path is achieved. Conductor widths should be maximized and lengths minimized. After you are satisfied with the power path, the control circuitry should be laid out. It is much easier to find routes for the relatively small traces in the control circuits than it is to find circuitous routes for high current paths. 2. The GND and SGND pins should be shorted right at the LTC1553L. This helps to minimize internal ground disturbances in the LTC1553L and prevents differences in ground potential from disrupting internal circuit operation. This connection should then tie into the
17
LTC1553L
APPLICATIONS INFORMATION
ground plane at a single point, preferably at a fairly quiet point in the circuit such as close to the output capacitors. This is not always practical, however, due to physical constraints. Another reasonably good point to make this connection is between the output capacitors and the source connection of the low side FET Q2. Do not tie this single point ground in the trace run between the low side FET source and the input capacitor ground, as this area of the ground plane will be very noisy. 3. The small signal resistors and capacitors for frequency compensation and soft start should be located very close to their respective pins and the ground ends connected to the signal ground pin through a separate trace. Do not connect these parts to the ground plane! 4. The VCC and PVCC decoupling capacitors should be as close to the LTC1553L as possible. The 10F bypass
VIN
+
CIN LO VOUT PVCC Q1 1 2 0.1F 3 G2 LTC1553L G1 20 19 18 17 16 15 14 13 12 11
1153L F10
+ +
COUT Q2
10F 0.1F
BOLD LINES INDICATE HIGH CURRENT PATHS
Figure 10. LTC1553L Layout Diagram
18
U
W
U
U
capacitors shown at VCC and PVCC will help provide optimum regulation performance. 5. The (+) plate of CIN should be connected as close as possible to the drain of the upper MOSFET. An additional 1F ceramic capacitor between VIN and power ground is recommended. 6. The SENSE pin is very sensitive to pickup from the switching node. Care should be taken to isolate SENSE from possible capacitive coupling to the inductor switching signal. A 0.1F is required between the SENSE pin and the SGND pin next to the LTC1553L. 7. OUTEN is a high impedance input and should be externally pulled up to a logic HIGH for normal operation. 8. Kelvin sense IMAX and IFB at Q1 drain and source pins.
+
10F
PVCC GND
OUTEN VID0 VID1 VID2
VID0 VID1 5.6k VID2 5.6k VID3 VID4 5.6k
4 SGND 5 6 RIMAX RIFB 7 8 9 10
VCC SENSE IMAX IFB SS COMP
VID3 VID4 PWRGD FAULT OT
CSS C1
RC CC
0.1F
LTC1553L
APPLICATIONS INFORMATION
VIN 5V
0.1F 5.6k 5.6k 5.6k VCC
PWRGD FAULT PENTIUM II SYSTEM 5V 1.8k DALE NTHS-1206N02 MOUNT THERMISTER IN CLOSE THERMAL PROXIMITY TO Q1 C1 150pF RC 8.2k CC 0.01F CSS 0.1F 5 OT
VID0 TO VID4 OUTEN COMP SS SGND GND SENSE
Figure 11. Single Supply LTC1553L 5V to 1.8V-3.5V Application with Thermal Monitor
PACKAGE DESCRIPTION
Dimension in inches (millimeters) unless otherwise noted. G Package 20-Lead Plastic SSOP (0.209)
(LTC DWG # 05-08-1640)
0.278 - 0.289* (7.07 - 7.33) 20 19 18 17 16 15 14 13 12 11
0.205 - 0.212** (5.20 - 5.38)
0 - 8
0.005 - 0.009 (0.13 - 0.22)
0.022 - 0.037 (0.55 - 0.95)
*DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
U
U
W
U
U
+
10F 2.7k 1N5817
+
CIN** 1200F x4
IMAX
PVCC G1
0.1F Q1* 20 LO 2H 18A vOUT Q2* COUT 330F x7
LTC1553L
IFB
+
G2
0.1F
*SILICONIX SUD50N03-10 **SANYO 10MV1200GX COILTRONICS CTX02-13198 OR PANASONIC 12TS-2R5SP AVX TPSE337M006R0100
1553L F11
0.301 - 0.311 (7.65 - 7.90)
1 2 3 4 5 6 7 8 9 10 0.068 - 0.078 (1.73 - 1.99)
0.0256 (0.65) BSC
0.010 - 0.015 (0.25 - 0.38)
0.002 - 0.008 (0.05 - 0.21)
G20 SSOP 0595
19
LTC1553L
PACKAGE DESCRIPTION
0.291 - 0.299** (7.391 - 7.595) 0.010 - 0.029 x 45 (0.254 - 0.737)
0.009 - 0.013 (0.229 - 0.330)
NOTE 1 0.016 - 0.050 (0.406 - 1.270)
NOTE: 1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS. THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
RELATED PARTS
PART NUMBER DESCRIPTION LTC1142 LTC1148 LTC1149 LTC1159 LTC1266 LTC1430 LTC1435 LTC1438 LTC1553 Current Mode Dual Step-Down Switching Regulator Controller Current Mode Step-Down Switching Regulator Controller Current Mode Step-Down Switching Regulator Controller Current Mode Step-Down Switching Regulator Controller Current Mode Step-Up/Down Switching Regulator Controller High Power Step-Down Switching Regulator Controller High Efficiency Low Noise Synchronous Step-Down Switching Regulator Dual High Efficiency Low Noise Synchronous Step-Down Switching Regulator 5-Bit Programmable Synchronous Switching Regulator Controller for Pentium II Processor COMMENTS Dual Version of LTC1148 Synchronous, VIN 20V Synchronous, VIN 48V, for Standard Threshold FETs Synchronous, VIN 40V, for Logic Threshold FETs Synchronous N- or P-Channel FETs, Comparator/Low-Battery Detector Synchronous N-Channel FETs, Voltage Mode Drive Synchronous N-Channel, VIN 36V Dual LTC1435 with Power-On Reset High Voltage Version of LTC1553L
20
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417 q (408) 432-1900 FAX: (408) 434-0507q TELEX: 499-3977 q www.linear-tech.com
U
Dimension in inches (millimeters) unless otherwise noted. SW Package 20-Lead Plastic Small Outline (Wide 0.300)
(LTC DWG # 05-08-1620)
0.496 - 0.512* (12.598 - 13.005) 20 19 18 17 16 15 14 13 12 11
NOTE 1
0.394 - 0.419 (10.007 - 10.643)
1 0.093 - 0.104 (2.362 - 2.642)
2
3
4
5
6
7
8
9
10 0.037 - 0.045 (0.940 - 1.143)
0 - 8 TYP
0.050 (1.270) TYP 0.014 - 0.019 (0.356 - 0.482) TYP
0.004 - 0.012 (0.102 - 0.305)
S20 (WIDE) 0396
1553lf LT/TP 0198 4K * PRINTED IN USA
(c) LINEAR TECHNOLOGY CORPORATION 1998

▲Up To Search▲

Price & Availability of LTC1553L

	To Download LTC1553L Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .